Citizen S4000DCM Instrukcja Użytkownika

LINE THERMAL PRINTER MODEL CT-S4000/CT-S4000DCCT-S4000L/CT-S4000DCLCT-S4000M/CT-S4000DCM User’s Manual

— 7 —Observe the following precautions for daily maintenance. When cleaning the printer, always turn it off and unplug it from thesupply outlet. Use

— 8 —THE TABLE OF CONTENTS1. GENERAL OUTLINE ... 91.1 Features ...

— 9 —1. GENERAL OUTLINEThis product are thermal line printers designed for use with a broad array ofterminal equipment including data, POS, and kitch

— 10 —1.2 UnpackingWhen unpacking the printer, confirm that the following are provided:● Printer: 1● AC power cord : 1 (for CT-S4000, CT-S4000L, CT-S

— 11 —1.4 Basic SpecificationsItem SpecificationsModel CT-S4000 PA/RS/UB, CT-S4000DC PA/RS/UBPrint method Line thermal dot print methodPrint width *1

— 12 —2. EXPLANATION OF PRINTER PARTS2.1 Printer AppearancePrinter coverPower switchOperation panelCover open buttonRear connector(Front view) (Rear

— 13 —● POWER LEDIlluminated when the printer power is on and off when the printer power isoff. May blink or light in a special mode or in case of fa

— 14 —2.2 Printer Cover Inside2.3 Other Built-in Functions● BuzzerThis printer has a built-in buzzer. It is operated in case of an error, operation

— 15 —3. PREPARATION3.1 Connecting the AC Power Cord1. Tu rn off the printer power switch.2. For AC power type (with built-in power supply), connect

— 16 —PrinterPin Signal2 TXD3RXD4RTS6 DSR7SG20 DTRPCSignal PinFG 1TXD 2RXD 3CTS 5DSR 6SG 7DTR 203.2 Connecting Interface CablesConfirm that the power

WEEE MARK,I\RXZDQWWRGLVSRVHWKLVSURGXFWGRQRWPL[ZLWKJHQHUDOKRXVHKROGZDVWH7KHUHLVDVHSDUDWHFROOHFWLRQV\VWHPVIRUXVHGHOHFWURQLFVSURG

— 17 —CAUTION!DO NOT connect any other device than the specified cash drawer to the cash drawerkick-out connector. (Also DO NOT connect a telephone li

— 18 —80mm 82.5mm58mmScales→ Partition→ CAUTION!When using 112 paper roll, the partition is not used.Partition3.4 Installing the PrinterThe printer c

— 19 —3.6 Setting DIP SwitchThe DIP switch is present on the serial interface board.The function of each switch is as shown below.Baud Rate (bps)Swit

— 20 —Sensor Position**1 φ21.0 φ18.0*2 φ24.5 φ21.53 φ28.0 φ25.54 φ31.5 φ28.05 φ35.0 φ32.05 φ21.0 φ18.04 φ24.5 φ21.53 φ28.0 φ25.52 φ31.5 φ28.01 φ35.0 φ

— 21 —4. MAINTENANCE AND TROUBLESHOOTING4.1 Setting/Replacing the paper roll4.2 Removing Jammed Paper1. Tu rn the printer power off.2. Open the pri

— 22 —CAUTION! Do not touch the surface of the heating element of the print head by bare hand ormetal. Wipe the dust off the surface of the platen p

— 23 —4.4 Self-printingInsert paper into the printer. With the FEED button pressed and held, turn theprinter power on, keep the FEED button held for

— 24 —4.6 Error Indication● Paper endPaper out is detected in two steps: paper near-end and paper end. ERROR LED willlight when the paper is empty.

— 25 —4.7 When the Paper Cover Cannot Be OpenedIf the cutter blade remains protruded due to paper jam or for any abnormality,opening the paper cover

— 26 —dD65~15044445.2 Printing PaperUse the print paper shown in the following table or the paper with equivalentquality.Paper Type Product NameRecom

IMPORTANT: This equipment generates, uses, and can radiate radio frequency energyand if not installed and used in accordance with the instruction manu

— 27 —When using “label paper” with CT-S4000L and CT-S4000DCL, refer to thefollowing. Use the following paper or the equivalent paper.Paper type Prod

— 28 —Black Mark (printed on the reverse)b) Black mark paper (BM paper)DBCAEFGCut positionPaper feedingdirectionPrintable areaMark Item DimensionsA Ri

— 29 —5.3 Manual Setting of Memory SwitchMemory switches can be set manually or by a command.For manual setting, refer to the next page.The function

— 30 —Switch No. Setting 0 (OFF) 1 (ON)Memory SW5-1 Buzzer Valid Invalid SW5-2 Line Pitch 360 406 SW5-3 USB Mode Virtual C

— 31 —1. Entering memory switch setting mode.Set paper in the printer and keep the printer cover open. With the FEEDbutton pressed and held, turn the

— 32 —5.4 Selecting Paper Type *L, *MPaper type selection is available by the combination of memory switches SW4-4 and SW4-5 by the used of “Memory S

— 33 —Level indicatorLEDLabel paper sensoradjuster *LBlack Mark papersensor adjuster1 Enter Adjusting Paper Sensor mode.Open the printer cover, remove

— 34 —5.6 Full cutting label paper *LWhen full-cutting the label paper with the printer installed horizontally,Be surethat the guide plate is mounte

TB74915-10F1.10E-0905

— 1 —GENERAL PRECAUTIONS● Before using this product, be sure to read through this manual. After having readthis manual, keep it in a safe, readily ac

— 2 —SAFETY PRECAUTIONS ... WHICH SHOULD BE STRICTLY OBSERVEDBefore using this product for the first time, carefully read these SAFETY PRECAUTIONS.Imp

— 3 — Do not use or store this product in a place where it will be exposedto:* Flames or moist air.* Direct sunlight.* Hot airflow or radiation from

— 4 —Do not use the printer under the following conditions. A state subject to vibration or unstable state. A state with this product slanted.• Oth

— 5 —PRECAUTIONS IN HANDLING THE PRINTERPlease observe the following precautions for power source and powercord: Do not plug or unplug the power cord

— 6 —Caution label is attached on the position shown in the following figure. Carefullyread the precautions in handling before using the printer.THES